Custom Car Decals shipped to Canada and USA!

family decals at decal fusion view your cart
Products and services
Application Instructions
We ship vinyl decals to CANADA or USA! Celebrating 17 YEARS ONLINE! Order Your graphics and we'll send them today. Pics of creations posted to our Facebook page daily.
Windshield Decal Instructions and Tips

Watch Instructional Videos

howto videoApply a decal using the simple method
Video won't load - click here

howto videoApply a family decal or any decal using the half and half method
Video won't load - click here

howto videoApply a windshield decal using the half and half method
Video won't load - click here

howto videoWet method (only for vehicle graphics and large solid decals)
Video won't load - click here

howto videoHow to easily Remove a decal from glass
Video won't load - click here

howto videoHow to install vehicle graphics or any large graphic using the wet method.
Video won't load - click here

stop decal videoClick here to STOP the VIDEO and View the 5 Most important tips for installing your decals

Faq for questions about your decals Decal Get Wrinkled in the mail? Click Here

Regular Decal instructions

  • Upon recieving your decal in the mail - unroll and layout flat. Lightly squeegee out any wrinkles caused by the shipping process.

1. Apply to the outside of a window or smooth painted surface. It's very important
to clean window or surface with rubbing alcohol not windex. Do not apply in direct
sunlight, apply in the shade. Do not apply if the tempurature outside is below 50 degrees. Also, trying the sample decal first will help if your unsure.


2. For larger decals some may prefer the wet installation. NOTE: The wet install works best
for solid decals without alot of small pieces, or small text.
Wet window with a heavy
mist of water, remove paper backing from decal and wet the sticky side with a mist
of water also. Apply the decal to the wet surface. After it is in the desired place,
squeegee out the water with a plastic squeegee. (You could use an I.D. Card for this.)


3. For smaller decals you can apply dry. Peel off the white paper backing and apply
the sticky part to the glass or surface. Applying from one side to the other will
reduce air bubbles. Rub or squeegee on with a plastic squeegee. ( I.D. Cards work too)


4. Now, Just peel off the remaining plastic or paper application tape very slowly at
a sharp angle away from the decal. If the decal starts to come up as well rub it
again or squeegee more then try again patiently.


5. Air bubbles happen. They are a normal part of this type of decal. If you would like
you can try to remove them by popping them with a pin and rubbing them, but most
will go away on their own. Wrinkles can usually be massaged away with a heat gun.


6. Maintainance tips: Do not over wax vehicle graphics. Using windex to clean the
decals may fade them faster. Most decals will last for several years but there is no
guarantee as to how long they will actually last.

Also see the F.A.Q. for more.

Exact Positioning Method

(also see pictures and step by step illustration below)

  • Upon recieving your decal in the mail - unroll and layout flat. Lightly squeegee out any wrinkles caused by the shipping process.

1. It's very important to clean window or surface with rubbing alcohol and apply in the shade. DO NOT apply in the sun or to hot glass. Do not apply if the tempurature outside is below 50 degrees. Also, trying the sample decal first will help if your unsure.


2. Tape decal to window like the picture below. Use 3 pieces of tape.
(2 in the middle, and 1 on one side as shown below.)

Exact positioning method for installing decals

3. You will be applying half of the decal at a time. One the side you didn't tape peel back
application paper revealing the sticky side, but not past the middle 2 pieces of tape.


4. Cut the white paper on the back near the center (Not the top part of the sticker, just the
bottom paper) and apply that side of the decal to the window from the center out preferably
using a squeegee. This "center out method" will reduce air from being trapped and creating
those annoying air bubbles.


5. Now since one side is stuck you can remove the remaining pieces of tape. Go to the other
side, lift the decal up and remove the rest of the paper backing from the center out. Apply
decal from the center out as well.


6. Now all you gotta do is remove the last layer of application tape from the window slowly
leaving only the decal cutout left on the window. Peel it slowly at a sharp angle away from
the decal.


7. Air bubbles happen. They are a normal part of this type of decal. If you would like you can
try to remove them by popping them with a pin and rubbing them, but most will go away on
their own. Wrinkles can usually be massaged away with a heat gun.


8. Maintenance tips: Do not over wax vehicle graphics. Using windex to clean the decals may
fade them faster. Most decals will last for several years but there is no guarantee as to how
long they will actually last.

Also see the F.A.Q. for more.

Pictures for the Exact Positioning Method....It's Easy!

We will use a family decal for this demonstration Tape Decal to surface as shown
1. Gather simple supplies. For this method you'll need tape, rubbing alcohol, scizzors, napkins, and a squeeqee or credit card. Clean the surface well with rubbing alcohol. 2. Tape Decal to surface as shown using three pieces of tape as shown. Masking tape works well. Make sure you tape it excactly where you want it because that's where it will end up.
Lift and cut the wax paper Ready to apply the first side
3. Peel back side without tape and cut wax paper underneath. You might want a friend to help hold the stick part so it don't fall back on the glass. 4. With the wax paper cut off on one side, get ready to apply half of the decal. Preferably using a squeegee or credit card applying from the center outwards to reduce air bubbles.
Squeegee the first side on Lift the second side of the sticker
5. Apply the one side from center outwards. 6. Remove the three pieces of tape now. Lift the other side.
Peel wax paper from second side Squeegee on the second side
7. Peel off wax paper backing from where you cut with the scizzors and hold the rest of the decal up and get ready to apply like you did the other side. 8. Squeegee the other side on as you did the first side. From the center out to reduce air bubbles.
VERY slowly peel application tape wow! That a great looking family sticker!
9. Once the whole decal is applied, very slowly remove the top layer of application tape at a sharp angle from the sticker. 10 . Da Da!! Don't That Look Great!
Free decalfusion decals
   
Positive SSL